ASME B16.10 Valve Face-to-Face Dimensions: An RFQ Checklist

B16.10 and B16.34 work together. B16.10 gives you the face-to-face dimension for installation interchangeability. B16.34 tells you whether the valve materials and pressure-temperature rating are suitable for your service conditions. Dimensional interchangeability under B16.10 does not by itself prove pressure-rating, material, or end-connection compatibility under B16.34. You must verify both standards when you qualify a supplier.

What to Put in Your RFQ

An RFQ that only says "valve per ASME B16.10" is incomplete. Because B16.10 dimensions depend on material, type, size, rating class, and end connection, your RFQ must state each of these explicitly.

Use this checklist when writing your valve RFQ:

• Valve type: gate, globe, check, ball, butterfly, plug, or other. B16.10 has separate tables for different valve types.
• Size: nominal pipe size (NPS) or DN, and if applicable, the specific size designation used in the B16.10 tables.
• Pressure class: class 150, 300, 600, 900, 1500, 2500, or other rating class referenced in the project code.
• End connections: flanged, threaded, welding end, or wafer/flangeless. The face-to-face dimension is defined differently for each.
• Material specification: ASTM or ASME material specification, such as A216 WCB, A351 CF8M, or A995. Material affects the applicable B16.10 table and also feeds into B16.34 pressure-temperature ratings.
• Standard edition: the exact edition of B16.10 your project requires, for example B16.10-2022.
• Supplementary requirements: any project-specific gasket, bolting, or leak-test requirements that may affect the valve face-to-face dimension or end connection.

Also ask the supplier to provide a dimensional drawing or datasheet showing the face-to-face (FTF), end-to-end (ETE), or center-to-face (CTF) dimension in millimeters and inches, and the applicable B16.10 table and edition.

Procurement Checks

When you receive quotations, do not accept a single line item that says "B16.10" without a dimension. Ask the supplier to confirm the exact face-to-face value that applies to your size and class, and the edition they used. Compare that value to the table in your project's specified edition.

For angle valves, verify the center-to-face and center-to-end dimensions. For straightway valves, verify the face-to-face and end-to-end dimensions.

Check that the end connection type matches what your piping system requires. A flanged valve has a different face-to-face dimension than a wafer valve of the same size and class. A welding-end valve may have an end-to-end dimension that assumes a certain bevel preparation.

If you are buying valves from a stockist or a manufacturer that also supplies pipe fittings, confirm that the valve dimensions are compatible with the mating flanges and the pipe components you already ordered. For the flange side, review the relevant flange standard and check the face-to-face distance against the flange faces. For pipe accessories, you can review the product options at pipe accessories and forged flanges and nonstandard forgings to understand the range of components your supplier can provide.

Inspection and Documentation

At the receiving inspection stage, measure the valve face-to-face dimension with a tape or caliper and compare it to the B16.10 table for the specified edition. Record the measured value in your inspection report.

Check the valve marking. B16.34 requires specific markings that include the manufacturer's name, valve type, size, class, material, and pressure-temperature rating. The marking must be legible and placed in a location that does not affect the pressure-containing envelope.

Request the following documents from the supplier:

• Material test certificates for pressure-retaining parts, referencing the ASTM/ASME material specification.
• Certificate of conformance to B16.10 and B16.34, stating the edition and any applicable supplements.
• Pressure test reports, including hydrostatic and shell test results, as required by B16.34.
• Nondestructive examination reports if required by the material spec or project specification.

Review these documents against your RFQ. If the supplier cannot provide the test reports or the dimensional report, treat the shipment as non-conforming until the documents are received.

Common Risks

Three risks are common when buying valves to B16.10.

Risk 1: Using the wrong edition. Face-to-face dimensions can change when ASME revises B16.10. If your project specifies one edition and the supplier uses another, the valve may not fit. Always state the edition in your RFQ and on the purchase order.

Risk 2: Mixing valve types and end connections. A gate valve and a globe valve of the same size and class do not necessarily share the same face-to-face dimension. Similarly, a flanged valve and a wafer valve are not dimensionally interchangeable just because they share the same pressure class. Confirm the exact type and end connection with the supplier.

Risk 3: Assuming B16.10 covers everything. B16.10 only defines dimensions for installation interchangeability. It does not provide pressure-temperature ratings, materials, or testing requirements. Those are covered by B16.34 and by the applicable piping code. A valve that is dimensionally correct may still be unsuitable for your service. Verify material, pressure-temperature rating, and end connections against B16.34 and your project's design conditions.

Sources

• B16.10 - Face-to-Face and End-to-End Dimensions of Valves
• B16.34 - Valves—Flanged, Threaded, and Welding End